Yamaha Tio 1608-D
Yamaha Tio 1608-D
Kaina 1499 €The Tio1608-D is a Dante-equipped I/O rack with 16 microphone/ line inputs and 8 line outputs. Tio racks feature the same recallable D-PRE™ microphone preamplifiers as the TF series delivering extraordinarily natural and musical sound. In combination with TF series consoles, Tio racks can be connected using up to three units with a fast and easy setup. * Optional NY64-D Card is required.
Gamintojas-
Technical Specifications of Tio1608-D/Rio
Tio1608-D Rio3224-D Rio1608-D Ri8-D Ro8-D Sound Philosophy Natural Sound Concept Grade D-PRE Inherit the sublime sound of PM series - Sampling Rate 44.1/48kHz 44.1/48/88.2/96kHz Indicators +48V Sig, Peak, +48V Sig Gain Compensation N/A Supported - HA Control Redundancy from CL/QL consoles N/A
(Primary only)Supported - Controllability from R Remote software Supported Maximum number of units using HA remotes per system Up to 3 Up to 8 - AD8HR mode (HA control from M7CL and LS9) N/A Supported - Analog Inputs 16 32 16 8 0 Analog Input Connector Combo Jack XLR-3-31 Type - Analog Outputs 8 16 8 0 8 AES/EBU Outputs 0 8 (4ST) 0 0 0 AC Inlet Normal V-Lock Type Heights 2U 5U 3U 1U 1U General Specifications
General specifications Tio1608-D Sampling frequency rate External 44.1kHz or 48kHz Total harmonic distortion Less than 0.1% +4dBu@20Hz-20kHz into 600Ω, Gain=+66dB / Less than 0.05% +4dBU@20Hz-20kHz into 600Ω, Gain=-6dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18dB/octave filter @80kHz Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT, Fs=44.1kHz or 48kHz Dynamic range 108 dB, INPUT to OUTPUT, Gain=-6dB / 112 dB, DA Converter Hum & noise level Equivalent input noise -128dBu, Gain=+66dB *Measured with A-weighting filter Residual output noise -88dBu, ST master off *Measured with A-weighting filter Crosstalk -100dB, adjacent INPUT/OUTPUT channels, Input Gain = -6dB *Measured with a -30dB/octave filter @22kHz Heat dissipation 100-240V, 50/60Hz, 43.5kcal/h Power requirements 100-240V, 50/60Hz Power consumption 50W Dimensions W 480mm (18-7/8") H 88mm (3-4/8") D 364mm (14-3/8") Net weight 5.7kg (12.6lbs) Accessories Owner’s Manual, Power Cord(2.5m), Rubber stoppers(4) Others Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃ Analog Input Characteristics
Input Terminals GAIN Actual Load
ImpedanceFor Use With
NominalInput Level Connector Balanced /
UnbalancedSensitivity*1 Nominal Max. before clip INPUT1-16 +66dB 7.5kΩ 50-600Ω Mics &
600Ω Lines-82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)Balanced -6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V) In these specifications, 0dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GNDAnalog Output Characteristics
Output Terminals Actual Source
ImpedanceFor Use With
NominalOutput Level Connector Balanced /
UnbalancedNominal Max. before clip OUTPUT 1-8 75Ω 600Ω Lines +4dBu (1.23 V) +24dBu (12.3V) XLR-3-32 type*1 Balanced In these specifications, 0dBu = 0.775Vrms.
*1.1: GND,2: HOT, 3: COLDDigital Input & Output Characteristics
Terminal Format Data length Level Audio Connector Primary/Secondary Dante 24bit or 32bit 1000Base-T 16ch ( Tio1608-D to other devises)
8ch (Other devises to Tio1608-D)etherCON Cat5e